An Annunciator panel also called Alarm Annunciators Panels or Centralized Warning Panel (CWP) or Caution Advisory Panel (CAP). These include a set of lights arranged in rows and columns which is then used as a central place to indicate the Read more…
The World Wouldn’t Turn Without Automation Technology Without automation technology, the reliability, efficiency, and quality of electric power systems, transportation systems, manufacturing operations and industry as a whole would diminish greatly. Industrial automation is found in almost every industry ranging Read more…
Thermocouples are the temperature sensors which are extensively used for the measurement of the temperature variations. They sense the temperature and the temperature is further measured by other instruments after sensing it. As they convert a non-electrical quantity (temperature) into Read more…
Motor Protection Circuit Breaker or MPCB Motor protection circuit breakers are a specialized type of electrical protection device that is designed specifically for electric motors, like their name implies. Electric motors are expensive equipment, so the role of the motor Read more…
ELECTRICAL CONDUIT An electrical conduit (EC) is a piping system that is used to carry electrical wiring for either power or communication. These piping systems are commonly referred to as raceways. The ECs are solid and they are used to Read more…
In Industrial Automation, generally when people say ‘interposing relay’ it means a general purpose relay that is used for interposing, meaning to separate or put a barrier between two circuits. Interposing relay normally consists of a coil that is energized Read more…
There is much doubt on this topic PTO and PWM. The Engineers using μ -controllers refer to Pulse Width Modulation regardless, if it is PTO or PWM. For PLCs it is important to know the difference. The automation training Read more…
Introduction The CAN bus was developed by BOSCH as a multi-master, message broadcast system that specifies a maximum signaling rate of 1 megabit per second (bps). Unlike a traditional network such as USB or Ethernet, CAN does not send large Read more…
WHY DO WE NEED SINGLE PHASE PREVENTERS The major cause of maximum motors burnout is overloading which occurs due to unbalance supply or single phasing. Phase failure occurs in case of fuse blown-off, loose connections or loss of phase from Read more…
Three phase induction motor is driven by AC supply. Because of low cost and more efficient, in industrial area, this motor is majorly used. It achieves High efficiency and reliable, Maintenance is not much needed, Compare than other Ac motors, Read more…
Our foundation-to-advanced automation course training covers end-to-end industrial workflows used in modern plants. Learners practice the full cycle from basic circuits to commissioning and maintenance with hands-on labs, project-based fault finding, SOP creation, and documentation exposure (URS, FDS, FAT/SAT).
This PLC training builds controller fundamentals with ladder, FBD, and ST, including I/O wiring, PID tuning, diagnostics, and version control practices on live rigs.
Our SCADA course covers tag databases, HMI graphics, historian/trends, alarm rationalization, redundancy, user security, backups, and deployment aligned to plant standards.
This panel design course teaches standards-compliant MCC/PLC panel engineering, SLD/GA/wiring docs, device selection, heat-load, testing, and FAT.
BMS training focuses on HVAC/lighting/utilities automation; CCTV & security covers design, storage, networking, and analytics.
The Industrial IoT diploma spans sensors-to-dashboard pipelines: MQTT/OPC UA, gateways, historians, alerts/KPIs, and predictive maintenance basics.
Locations: Mumbai (Vashi), Pune (Chinchwad), Maharashtra, Kolkata, West Bengal, Madhya Pradesh, Chhattisgarh, Jharkhand, Hyderabad (Ameerpet), Bangalore (JP Nagar), Mysore (Vijayanagar 2nd Stage), Karnataka, Chennai (Anna Nagar West Extn), Tambaram (West Tambaram), Tamil Nadu, Tiruchirappalli (Chatram), Erode, Madurai (K. Pudur), Tirunelveli (Vasanth Nagar), Coimbatore (Hope College), Palakkad (Sultanpet), Pathanamthitta (Chittoor), Kottayam, Malappuram (Perinthalmanna), Thrissur (Keerankulangara), Kannur (Thana), Kollam (Chinnakada), Thiruvananthapuram (Thampanoor), Kozhikode (Mavoor Rd Jn), Kochi (Kaloor)